Gas, High-Pressure & Vacuum Piping for Demanding Applications
From gas supply to high-pressure and vacuum applications, we plan, install and test piping based on your process requirements.
High-Pressure Piping for Industrial Applications
- Compressed air at high pressure for bottle filling and testing
- Hydraulic and pneumatic test benches
- Nitrogen and inert gas supply at high pressure
- Gas booster and cylinder filling stations
- Pressure vessel and receiver connections
- Process lines in chemical and engineering plants
Design review
We confirm the working pressure, the gas and the temperature before choosing anything.
Material and rating selection
Pipe, fittings and valves chosen with a safety margin above your working pressure.
Clean preparation
Tubes are cut square, deburred and cleaned, so joints seat correctly.
Joint making
Compression or welded joints made by trained fitters, to the method that suits the line.
Support and protection
Firm supports and guards that keep lines secure and limit vibration.
Pressure test and record
The line is tested above working pressure and the result is recorded.
| Item | Typical options |
|---|---|
|
Pipe and tube |
Seamless stainless steel (304 / 316), carbon steel |
|
Joints |
Compression (ferrule) fittings, welded, threaded |
|
Valves |
High-pressure ball, needle and check valves |
|
Pressure range |
From medium pressure up to several hundred bar, as designed |
|
Testing |
Hydrostatic or pneumatic test above working pressure |
|
Design reference |
Process piping codes such as ASME B31.3, where required |
Gas Piping Systems for Industrial Gases
- Nitrogen and argon distribution to production points
- Oxygen supply for cutting, furnaces and processing
- Carbon dioxide lines for welding and beverage use
- Gas cylinder manifold and bank connections
- LPG and PNG supply to ovens, burners and boilers
- Laboratory and cleanroom gas lines
Gas and material check
We confirm the gas, its purity needs and the pipe material suited to it.
Route and safety plan
We plan the route, ventilation, isolation valves and safe distances before work starts.
Cleaning for service
Lines for oxygen and high-purity gas are cleaned and kept free of oil and dust.
Fitting and joining
We join with fittings and methods suitable to the gas and pressure.
Leak testing
Every joint is tested for leaks before the gas is introduced.
Purge and commissioning
The line is purged, checked at each outlet and handed over with its valve positions marked.
| Item | Typical options |
|---|---|
|
Pipe material |
Stainless steel, copper, brass, aluminium, chosen to suit each gas |
|
Joints |
Compression fittings, brazed, welded or threaded, by gas and pressure |
|
Gases covered |
Nitrogen, argon, oxygen, carbon dioxide, LPG, PNG |
|
Purity care |
Oil-free cleaning for oxygen and high-purity lines |
|
Control |
Isolation valves, regulators, gauges and non-return valves |
|
Testing |
Leak test with a suitable test gas or soap solution |
Vacuum Piping for Reliable System Operation
- Packaging machines and vacuum sealing
- Pick and place and suction handling
- Vacuum pumps serving several machines from one plant
- Plastic moulding and thermoforming
- Laboratory and pharmaceutical processing
- Degassing and drying operations
Vacuum target
We confirm the vacuum level and flow each machine needs.
Line sizing
We choose larger bores and fewer bends, because narrow or twisting lines cut vacuum performance.
Joint selection
We use fittings and seals made to hold vacuum, not only pressure.
Clean installation
Pipes are cleaned and joined carefully, so no particles reach the seals.
Leak-rate test
We draw the line down and watch for vacuum loss over time.
Fault tracing and handover
Any leak is traced and fixed, then the system is handed over with test results.
| Item | Typical options |
|---|---|
|
Pipe material |
Stainless steel, aluminium, engineered plastic |
|
Vacuum level |
Low to medium industrial vacuum, as designed |
|
Joints |
Vacuum-rated push-fit, coupler or flanged joints |
|
Seals |
O-rings in suitable rubber grades |
|
Line layout |
Large bore, short runs, few bends |
|
Testing |
Vacuum decay (leak-rate) test |
Industries We Serve With Gas, Pressure & Vacuum Piping
Pharmaceutical
Clean gas and vacuum lines for processing and packing.
Food and Beverage
Carbon dioxide, nitrogen and vacuum lines for filling and sealing.
Packaging
Vacuum and gas lines for sealing, flushing and handling.
Laboratories and Research
Controlled gas and vacuum supply for testing and analysis.
Need Help With Your Gas, Pressure or Vacuum Piping?
Share your gas type, pressure or vacuum level and plant layout. We’ll recommend suitable piping and joints for your application.
Frequently Asked Questions
Can you install a high-pressure pipe for an existing industrial setup?
Yes. We can assess your existing equipment, operating pressure, connection points and available routing before recommending a suitable piping arrangement. Our team can handle the required installation based on the application and site conditions. If you are looking for a high pressure pipe in Mumbai, we can also discuss the pipe and fitting requirements for your system.
Can you replace a damaged section of an existing high-pressure pipeline?
Yes. If only a particular section is damaged, leaking or no longer suitable, we can inspect the line and replace the required pipe, fitting, valve or joint instead of replacing the complete pipeline. The replacement is selected according to the operating pressure and application. This makes us a suitable option when you need a high pressure pipe in Mumbai for an existing system.
Can you extend an existing vacuum piping system for a new machine?
Yes. We can review the existing vacuum line, available capacity and new machine requirements before planning an extension. The additional piping can be routed according to the required vacuum level, flow, pipe size and connection points. If you are looking for a vacuum pipe in Mumbai, we can assess your existing system and recommend a suitable configuration.
Can you modify vacuum piping when machinery is relocated?
Yes. When equipment is moved within a plant, the existing vacuum connections may need to be rerouted or extended. We can assess the new machine location and plan the required changes while considering the existing vacuum network and available space. This can include supplying and installing the required vacuum pipe in Mumbai
Can you install a gas pipeline for PNG applications?
Yes. We can plan and install piping for PNG applications based on the gas requirement, operating pressure, equipment connections and plant layout. The routing and connection arrangement are planned according to the application and site conditions. For businesses looking for a gas pipeline in Mumbai for PNG systems, we can assess the requirement and recommend a suitable piping arrangement.
Can you install nitrogen gas piping for industrial applications?
Yes. We can provide piping for nitrogen applications such as equipment supply, purging and other industrial requirements. We consider the required pressure, flow, purity, connection points and plant layout when planning the system. If you need a gas pipeline in Mumbai for nitrogen, we can assess the application and plan the required piping accordingly.
